Видео

Klo boleh tau, enakan pake buatan pabrik atau buatan sndiri pak 😁

😢please tell me where i can buy this in india

Super

What kind of rod is it ? Threading ?

Use 2 half nuts with a spring and another cam locking the micro adjuster to eliminate backlash.

Di menit 3:40 kayunya tiba" beda? Dan di menit 4:49 baut hasil potongan ga sejajar dengan kayu? Dimenit ke 5:00 baut hasil potongan tiba" sejajar dengan kayu? Mohon pencerahan nya?ada yg bisa jelaskan..😊 ?

saya melalang buana di dunia luar, namun banyak sekali orang indo kreatif yang bermunculan. mantap bang.

Great project.thanks

masih lurus sampe hari ini bang

Siap selalu menyimak pak, semoga ada reseki bisa, membeli untuk di bengkell👍👍🎉

Makasi atas, pengetahuan nya pak, siap selalu menyimak.. 👍👍

Another nice copied project. Do you actually make anything yourself? Or is everything copied and then claimed by you as your own? Just blatant copying stuff without giving credit.. This is a John Heisz design...

Om ijin bertanya. Mesin nya harus menggunakan air kran ato air dalam ember

Sistem pembelian gimana mas jon

Fan empelar

Thanks!

Semoga bisa kebeli mesin bubut yg belasan juta

Hadir nyimak bang.

You should have some large mesh over the fan inlet in case any plastic or large wood goes up and into the fan it doesn't just explode 😅 And make a box around the motor/fan with some insulation to reduce noise some more even tho it is pretty quiet it's always nice to get a little more silent 😁 And have a grounding wire to the cyclone and air pipes with a few screws through it to the inside to prevent static

Very nice work 😁

Wonderful

You don't need to reduce the diameter of the impeller to reduce the power draw (watt/Amps) just reduce the inlet opening. And for more airflow most centeifugal fans is actually curved the other way around i think it's called "foreward facing" and you can also make it just straight vanes for a little more noise. And for power tuning waith untill most air hoses/ducts are connected and then measure the power and restrict the inlet until the rated power. Plus or minus 10% should be ok but better to be a little low

اريد الخطط لترابيزة المنشار خاصتك

About how much cheaper is it to make your belts verses buying them premade not counting all the time, epoxy, knife blades.

Kelebihan sama kekurangan nya apa min?

Hadir om ❤❤❤

Bang Jhon... Kalau di banding tekiro gimna

Cap mata sama tekiro bagus mana om ?🙏

من اين احصل علي الخطط

Taneman gergaji tukang kayu saya.. Super tajam gergaji hanya sekejap

Klau beli berapa pak yg sekn

Apa meja saw di jual mas arief

Buat nebang pohon bisa ga om?

Gergaji Jepang bisa diasah gak om?

Hafir om....sering sering muncul lagi di RUclips om ❤🙏💪💪

thank you very much ..

10 minutes for colecing material an may be not enough 😅😅

Review produknya jelas, lugas dan apa adanya. Bawaannya juga santai tapi jelas. Salam kenal dr subscriber baru Bang. Salam sehat dan sukses dr penggemar power tools Surabaya 🙏👍

Luarrrr biasa 👍👍👍👍

Muze yh chiar chahiye kha mileg i btao

aku mau beli...minta wa

bang kalo dijadiin pengganti dinamo buat mutar beban 1kintal bisa ga

kalau beli di mana bro

good to get a few measurements thanks, vital to know the belt size please

Ya done good, real good!

Very nice my friend!👍👍👍

Berapa harganya 1260-118

Untuk baterai 24 V dan 588 V apakah juga cocok?

Gergaji yg tajam itu bro ketika digunakan motong kayu dia terdengar renyah bro.!

With work, I can get a board flat with a "manual" hand plane.. but, have grown weary of it. Got an electric one earlier this year, and its defect is like your first example. Thanks for this tutorial!